Please use this identifier to cite or link to this item: https://elib.psu.by/handle/123456789/33012
Title: Влияние деформации на механические свойства луженой жести
Authors: Дьяконов, В. А.
Пилипенко, С. В.
Штемпель, О. П.
Dʹyakonov, V.
Pilipenko, S.
Shtempelʹ, O.
Other Titles: Influence of Deformation on the Mechanical Properties of Tin-Plated Tin
Issue Date: 2022
Publisher: Полоцкий государственный университет имени Евфросинии Полоцкой
Citation: Дьяконов, В. А. Влияние деформации на механические свойства луженой жести / В. А. Дьяконов, С. В. Пилипенко, О. П. Штемпель // Вестник Полоцкого государственного университета. Серия B, Промышленность. Прикладные науки. - 2022. - № 10. - С. 18-24.
Abstract: Рассмотрено влияние деформации на механические свойства характерных слоев жести при прошивке в ней сквозного отверстия. Получены графические зависимости, показывающие изменение микротвердости наружных и внутренних слоев луженой жести по толщине материала листа в зависимости от угла его изгиба. Изучена целостность наружного луженного слоя белой жести в готовом изделии. Установлено, что целостность покрытия сохраняется вплоть до места пластического разрыва прошивнем пресса центральной части заготовки. Анализ распределения значений микротвердости показал, что внутренний слой имеет более высокие значения, чем наружные, максимальное значение степени наклепа наблюдается в наружном слое (+17,1%). При значениях угла изгиба более 150о значения степени наклепа во всех слоях стремятся к одному значению (примерно 12,75%). Согласно анализу графика изменений степени наклепа слоев листа вдоль линии изгиба образца, степень наклепа серединного слоя происходит при любом изменении формы листового материала независимо от степени наклепа наружных слоев.= Annotation. The influence of deformation on the mechanical properties of the characteristic layers of tin plate when a through hole is pierced in it is considered. Graphic dependences are obtained showing the change in the micro hardness of the outer and inner layers of tinned tin along the thickness of the sheet material depending on the angle of its bending, the integrity of the outer tinned layer of tinplate in the finished product is studied. It has been established that the integrity of the coating is preserved up to the point of plastic rupture by the piercing of the press in the central part of the workpiece. An analysis of the distribution of microhardness values showed that the inner layer has higher values than the outer ones, the maximum value of the hardening degree is observed in the outer layer (+17,1%). At val ues of the bending angle of more than 150 degrees, the values of the degree of hardening in all layers tend to the same value (approximately 12,75%). Analysis of the graph of changes in the degree of hardening of the sheet layers along the bending line of the sample showed that the degree of hardening of the middle layer occurs with any change in the shape of the sheet material, regardless of the degree of hardening of the outer layers.
URI: https://elib.psu.by/handle/123456789/33012
metadata.dc.rights: open access
Appears in Collections:2022, № 10

Files in This Item:
File Description SizeFormat 
18-24.pdf436.63 kBAdobe PDFView/Open


Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.